Penatron 1007

Product Description

Penatron 1007 is a two-component, rapid set, high performance, 100% polyurea elastomer spray coating formulated for high physical properties, hydrolytic stability, and low permeability.** Designed for extremely high performance, Penatron 1007 is a 100% solids material.

 **Formulated for flexibility, toughness, high tensile strength and adhesion with excellent chemical and fuel resistance.

• 5-8 SECOND SET TIME
• TACK FREE IN 30 SECONDS
• HIGH BOND STRENGTHS TO SUBSTRATE
• 600% ELONGATION

The 1007 is a true polyurea and not a hybrid product.   Application substrate temperatures are 20°F to 200°F.  Penatron 1007 is applied via Gusmer heated equipment such as the HV-20/35 or larger. 1007 conforms to the requirements of the USDA for incidental food contact.
 
Advantages

• SUPERIOR ELONGATION – 600%+
• EXCELLENT FOR CONTAINMENT, REFINERIES, CHEMICAL PLANTS, MARINE APPLICATIONS AND OTHER INDUSTRIAL FACILITIES
• DESIGNED TO CHEMICALLY BOND TO ASTC PRIMERS
• 1007 FORMS A NEARLY INDESTRUCTIBLE PROTECTIVE BARRIER ON ANY SURFACE IT IS APPLIED TO
• DESIGNED EXCEPTIONALLY CHEMICAL RESISTANT.
• EXTREMELY TOUGH: HIGH IMPACT & ABRASION RESISTANCE
• CURES RAPIDLY AND EFFICIENTLY, WITH LITTLE ODOR

USES AND AREAS

• ROOFING SYSTEMS
• NON-SKID SURFACES, REQUIRING HIGH IMPACT AND/OR CHEMICAL RESISTANCE
• CORROSIVE BARRIER, PROTECTIVE COATING PROTECTION - PROCESSING EQUIPMENT
• CONCRETE TANKS &  STEEL TANKS
• SECONDARY CONTAINMENT – WALLS AND FLOORS
• ALL INDUSTRIAL SERVICE SURFACES
• WATERPROOFING/ FOOD PROCESSING
• WHEREVER A MONOLITHIC MEMBRANE IS NEEDED WITH SUPERIOR PHYSICAL PROPERTIES

General Physical Characteristics

Moisture Vapor Reduction:  Penatron 1007 should be applied to concrete surfaces as part of a "coating system” in which ASTC moisture vapor barriers and primers are used.  Since concrete will "out-gas,” using the CMW 8000 moisture vapor barrier treatment and the Penprime 7001 primer prior to application of the 1007 is the best way to reduce the effects of concrete "out-gassing.”  When using this system, the coating achieved is seamless, aesthetically pleasing, exceedingly tough, and guaranteed to last a very, very long time.

Priming:  Penatron 1007 is specially engineered to chemically cross-link ("bond with”) with the ASTC primer Penprime 7001.  When applied together, the primer and coating actually chemically bond together to form a truly superior substrate coating system. 

Notes on application:  The best spray application results are obtained when the ambient temperature is decreasing.  Out-gassing will decrease as temperature falls. In applications where it is not possible to use the temperature to your advantage, it is suggested that the ASTC’s CMW be used in conjunction with Penprime 7001 or 6012-2F epoxy prior to the polyurea coating.

Preparation: Concrete must have a minimum 28-day cure prior to application.  Remove any curing agents, form release materials, oils, waxes, moisture or any materials that may prevent the product from successfully bonding to the substrate.  Clean and wash to remove contaminants and maintain pH 8.0-11.0.

*Perform a Moisture Vapor Test before making a coating application on concrete.
Provide rough profile of a minimum of 2 mils.   
Review ASTM D4259 Abrading Concrete and ASTM F1869 Measuring Moisture Vapor Emission.  Seal/repair all bug-holes, cracks and spalls; see ASTC data sheets on 830, 4034 and 3004 (joints).
Steel – Near white sand blast per SSPC-SP10/NACE 2.  Welds, seams, edges, etc. – grind/blast smooth and provide 2 mil profile.  Immersion – review SSPC-SP1.

Application: Use only Gusmer or Graco heated, high pressure spray equipment & impingement gun.  Maintain a fluid pressure minimum of 2,000 psi and minimum heat 160ºF.  Substrate Surface temperature should be -20ºF to 120ºF.  Apply at no less than 5ºF above dew point.  
**Please note that Spraying Penatron 1007 requires specialty spray equipment.  Therefore, the applicator must be a professional qualified in the use of high heat/pressure spray equipment and specialty polymers.

Color:  Black, Dark Gray, Khaki Tan.  Note that Aromatic systems will shift color from exposure to ultraviolet radiation (i.e. sunlight).  The Khaki Tan color will resist changing color most efficiently.  Aliphatic top coats (i.e. Penatron 5500) are often used to provide stable color.

Limitations:  Do not use on wet surfaces or expose part A to moisture.  Keep drums out of direct sunlight and store drum kits on wood pallets at room temperature. Always mix part B before using. Pre-heat drums as needed per environmental temperature.  Best results over vapor barrier and/or compatible primer.

Shelf Life:  1 year; store between 40°F and 100°F.
Solids:  100%
Components:  Two part system; 1:1 ratio
Packaging: 10 Gallon Kits & 110 Gallon Kits 
VOC Content:  0gms/1 or 0.0 lbs/gal

This product is for use by professional applicators only. Wear Protective Clothing. Read MSDS before using this product. DOT/Flash Point – Non-flammable Liquid Classification, not regulated. Warranty:  See ASTC Polymers, Inc. Warranty data sheet.  (8/05) Product data sheets subject to change without notice.  © 2005 ASTC Polymers, Inc.