Penatron 1006

Product Description

Penatron 1006 is a two component, high wet-out, long open time, aromatic MDI and multifunctional polyurea amine blend.  The polymer system is "pure polyurea" and is not modified using urethane or other additives.  

Unique Properties

• SLOW GEL & SET TIME
• HIGHER BOND STRENGTHS TO SUBSTRATE DUE TO SLOWER SET TIME AND "WET-OUT",
• GREATER PENETRATION INTO FABRICS AND REINFORCING MATTING
• HIGHER OVERALL TENSILE STRENGTH WHEN NEAT AND EXTREMELY HIGH WHEN USED AS A PENETRATING POLYUREA AMALGAM/FABRIC SYSTEM
• EXCELLENT IN MARINE ENVIRONMENTS
• HIGH HYDROLYTIC STABILITY

The polyurea structure is very durable with 100% solids and a set time of 6 to 8 minutes. This aromatic polyurea is extremely tough with excellent adhesive properties and  very good chemical resistance.  Penatron 1006 is applied via high pressure heated equipment such as the HV-20/35 or larger.  It conforms to the requirements of the USDA for incidental food contact. It is formulated to be hard, non-brittle, flexible, fast set with impact and abrasion resistance. Gel Time is 65 seconds allowing approximately two to three minutes for self leveling or for broadcasting  aggregate into the product.   

Advantages

• "SLOWED" SET TIMES - 6 TO 8 MINUTES
• EXCELLENT BOND DEVELOPMENT & BETTER "WET-OUT"  CONTACT TIME
• DESIGNED TO CHEMICALLY BOND TO ASTC PRIMERS
• EXCELLENT WITH REINFORCING FABRICS.
• PROTECTS CONCRETE AND OTHER SURFACES, WOOD, METAL, ETC.
• CHEMICAL RESISTANT, HIGH IMPACT & ABRASION RESISTANCE, TACK FREE IN 6 - 9 MINUTES
• 100% SOLIDS, NO VOC PROBLEMS, NO ODOR

Use Areas

• ROOFING SYSTEMS
• SECONDARY CONTAINMENT WITH NON-SKID
• CORROSIVE BARRIER, PROTECTIVE COATING PROTECTION - PROCESSING EQUIPMENT
• CONCRETE TANKS & STEEL TANKS
• SECONDARY CONTAINMENT WALLS AND FLOORS
• ALL INDUSTRIAL SERVICE SURFACES

General Physical Characteristics

Moisture Vapor Reduction:  Penatron 1006 should be applied to concrete surfaces as part of a "systems approach".  Use with CMW  vapor barrier treatment for the concrete and the Penprime 1 as the primer, pinholes are reduced.  

Color:  Black, Medium Gray, Kaki Tan.  Note: Aromatic systems will shift color from exposure to UV.  Dark colors resists color change more then light colors.  

Preparation: Concrete must have a minimum 28 day cure prior to application.  Remove any curing agent, form release materials, oils, wax, moisture or any material that may effect bonding.  Clean and wash to remove contaminants and maintain pH 8.0-11.0.
*Perform a Moisture Vapor Test before making the coating application on concrete.  Provide rough profile minimum 2 mils.   Review ASTM D4259 Abrading Concrete and ASTM F1869 Measuring Moisture Vapor Emission.  Seal/repair all bug-holes, cracks and spalls, see ASTC data sheets on 830, 4034 and 3004 (joints). Steel; Near white sand blast per SSPC-SP10/NACE 2.  Welds, seams, edges, etc. grind/blast smooth and provide 2 mil profile.  Immersion – review SSPC-SP1.

Prime:  Prime when needed with ASTC primer Penprime 7001 or 6012-2F moisture tolerant epoxy.
Prime 1 to 2 hours prior to the 1006 application for best results.  Avoid heavy mil thickness of primer, maintain mil profile with primer. Steel; prime immediately after cleaning to avoid flash rusting.  

Application: Use only Gusmer or Graco heated high pressure equipment & impingement gun equipment, fluid pressure of 2,000 psi.  Minimum heat 160ºF.  
Surface temperature -20ºF  to 120ºF.  Apply at not less than 5ºF above dew point.
Apply at specified mil thickness over primer as required for the application.  
Spraying Penatron 1006 requires special equipment, user must be a professional applicator qualified in the use of high performance polyurea materials and specialty application equipment.  Use OPEN time for aggregate broadcasting, seed aggregate no longer then 2 to 3 minutes after the product has been applied.

Limitations:  Do not use on wet surfaces or expose part A to moisture.  Keep out of direct sunlight, store drum kits on wood pallets at room temperature. Always mix the part B before using. Pre-heat drums as needed per environmental temperature.  Best results over vapor barrier and/or compatible primer.  Protect from cold during storage and shipping. 

Shelf Life:  1 year, store between 40°F and 100°F.
Packaging: 110 gallon kits 

VOC Content:  0gms/1 or 0.0 lbs/gal

This product is for use by professional applicators only.  Wear Protective Clothing.  Read MSDS before using this product.  DOT/Flash Point – Non-flammable Liquid Classification, Warranty:  See ASTC Polymers, Inc. Warranty data sheet.  (8/08) Product data sheets subject to change without notice.  © 2008 ASTC Polymers, Inc